Xp Deus 2 Version 3.10 update released - this is non beta version

[Tnsharpshooter]

https://m.youtube.com/watch?v=a3-LtBRE02Q

https://www.xpmetaldetectors.com/en/ba/ ... update.php

[Tnsharpshooter]

Some differences noted when using FMF or HF2 coils.
https://m.youtube.com/watch?v=Dc-m-muSA3I

[Tnsharpshooter]

Version 3.10 shown with both hf2 and FMF coils.
This is a departure from previous versions designed only to run FMF coils.
https://m.youtube.com/watch?v=EGSFJTzeVUM

[Tnsharpshooter]

More freq info- Saved Programs.
https://m.youtube.com/watch?v=8lqoFLwwOSc

[Tnsharpshooter]

Might be a good video for hf2 owners to watch.
https://m.youtube.com/watch?v=EXxwwklit7Y&t=33s

[Tnsharpshooter]

Video comparing Deus 2 hf2 coil and Manticore M8 coil. Lead shot masking tests using clad dime and 10 k gold ring.
https://m.youtube.com/watch?v=UnhJdf_fJas

[Tnsharpshooter]

Deus 2 hf coil and Manticore with M8 coil compared small foil and gold ring tests.
https://m.youtube.com/watch?v=Rt27zSesXmE&t=21s

[NASA-Tom]

The higher the Freq............. the more hyper-sensitive the unit(s) will be with the #5 shot.,.,.,., and the ID's will 'express' accordingly.

Did you use All Terrain - High Conductors.....when you had the dime under the #5 shot? (This is important)!
Any time the camera was close to the faceplate of the detector.......... the camera nearly completely missed the faceplate. (Due to camera fixed position). Plus....... the 'glare' was blinding. It's difficult to capture a mirror/glass faceplate!

There is a misnomer in regards to Recovery Speed (either detector).
Recovery Speed is designed for ADJACENT targets. (((In other words: Lateral separation))).
Targets that are superimposed (on top of each other......with-or-without: vertical separation)..... Recovery Speed will have minimal effect.

[Tnsharpshooter]

Potential Bug V3.10 HF2 coil shown.
https://m.youtube.com/watch?v=ZdYXri-HN ... p=2AENkAIB

Follow up video showing potential bug.
https://m.youtube.com/watch?v=v926k2-4YxQ

9” FMF demo. Comparing SENS and SENS FT disc 6.8 silencer -3.
https://m.youtube.com/watch?v=gsjOmvo1Kxw&t=9s

9” FMF demo. Comparing SENS and SENS FT horizontal nail and Nicker 6.8 disc. -1 silencer. Here the Sens ft wins. Hmm
https://m.youtube.com/watch?v=ewFT_q4N8 ... cJAYcqIYzv

[Tnsharpshooter]

The higher the Freq............. the more hyper-sensitive the unit(s) will be with the #5 shot.,.,.,., and the ID's will 'express' accordingly.

Did you use All Terrain - High Conductors.....when you had the dime under the #5 shot? (This is important)!
Any time the camera was close to the faceplate of the detector.......... the camera nearly completely missed the faceplate. (Due to camera fixed position). Plus....... the 'glare' was blinding. It's difficult to capture a mirror/glass faceplate!

There is a misnomer in regards to Recovery Speed (either detector).
Recovery Speed is designed for ADJACENT targets. (((In other words: Lateral separation))).
Targets that are superimposed (on top of each other......with-or-without: vertical separation)..... Recovery Speed will have minimal effect.

I didn’t show ATHC when showing the shot. I did show it using small foil masker comparing modes.
I just showed speed setti;g changes. Because there are always those out there that try to find fault with my results - they may say I.e you didn’t check with X speed.